Interphone dustproof and waterproof grade standard

Interphone dustproof and waterproof grade standard shared by waterproof Marine Radio supplier.

The IP rating system provides a method of classifying products by the degree of dust, water and collision resistance of electrical appliances (including walkie-talkies, radio equipment, etc.) and packaging. This system is recognized by most European countries and is announced in the IPcode (outer packaging protection rating) of IEC529(bsen60529:1992). The protection level is usually expressed by IP followed by two Numbers, which are used to specify the protection level. The first number indicates the extent to which a device is resistant to dust, or how safe people are from harm in a sealed environment. The second number indicates how waterproof the equipment is.

The description of solids

0: indicates no protection;

1: The table can resist the entry of solid substances over 50 mm, for example, accidental touch of hand;

2: means it can resist the entry of solid substances with a diameter of more than 12 mm and a length of less than 80 mm, such as fingers;

3: means that it can resist the entry of solid materials, such as tools or metal wires, exceeding 2.5 mm;

4: It can resist the entry of solid substances over 1.0 mm, such as small metal wires;

5: dustproof, limited access (no harmful accumulation)

6: it is difficult for dust to enter and completely dustproof;

The description of the liquid

0: indicates no protection;

1: represents the water point that can withstand vertical fall;

2: can withstand the direct injection of water spray at a 15° vertical Angle;

3: can withstand a 60° vertical Angle of the spray direct injection;

4: can withstand the spray from any direction -- limited access is allowed;

5: Withstand low-pressure water jet from all directions -- limited access allowed;

6: it can withstand strong water jet and allow limited access;

7: it means that it is allowed to be briefly put into 15 cm to 1 m deep water for up to 30 minutes;

8: can withstand long-term immersion under pressure;

VHF Marine Radio Supplier shares that the waterproof level of the electronic measuring instrument also reflects the ability of the instrument to prevent moisture and dust, especially for outdoor activities, the rabbit can not be in the harsh environment of high humidity or dust, the sealing and waterproof ability of the instrument is crucial to ensure the safe operation and life of the instrument. To this end, the international formulation of the IEC529 standard. In order to adapt to this, the Japanese industry standard will be electronic instruments (also applicable to walkie-talkies and radio equipment) waterproof protection into 10 grades, respectively by IPX1, IPX2...... Said. Meaning of protection class:

0: unprotected;

1: drip-proof type I drops falling vertically have no harmful effects;

2: droplet proof type II has no influence of kiln on the droplet falling within a range of 15 "in the vertical direction;

3: Rainproof type has no influence on rainfall within 60 degrees of vertical direction;

4: Splash proof type is free from harmful influence by water splashing in any direction;

5: anti-spray type is directly affected by water injection in any direction without harmful effects;

6: water resistant type of any direction directly under the water injection is not internal;

7: anti-flooding type in the specified conditions even if submerged in water is not all allowed inside;

8: water medium long time submerged in a certain pressure of water can be used;

9: anti-humidity type in the relative humidity of 90% to divine moisture sample used;

International industry standard waterproofing registration IP grade for dust control shared by Waterproof Walkie Talkie Supplier.

IPxx dustproof and waterproof grade

Dust level (first X)

Waterproofing grade (second X)

0: no protection 

1: to prevent the invasion of large solid;

2: Prevent invasion of medium sized solid;

3: Prevent the invasion of small solids;

4: prevent solid objects larger than 1mm from entering;

5: prevent harmful dust accumulation;

6: completely prevent dust from entering;

0: no protection 1: water drops into the shell has no impact;

2: when the shell 0f the water-proof radio tilts to 15 degrees, water drops into the shell without impact;

3: water or rain from the corner of 60 degrees to the shell without impact;

4: liquid from any direction to the shell without damage;

5: Rinse with water without any injury;

6: can be used in cabin environment;

7: resistant to flooding in a short time (1m)

8: soak for a long time under certain pressure

Example: the scale or display instrument is marked IP65, which means that the product can completely prevent dust from entering and can be washed with water without any harm.

IPXX grade on the provisions of the waterproof test.

(1) the IPX 1

Test equipment: drop water test device sample placement: the sample shall be placed on a rotating sample table at the normal working position of the sample at 1r/min, and the distance from the top of the sample to the dripping mouth shall be no more than 200mm. Duration: 10 min.

(2) the IPX 2

Test equipment: test device for dripping test: make one side of the sample form a 15° Angle to the vertical line, and the distance from the top of the sample to the dripping mouth is no more than 200mm. Change another side after each test for four times. Test conditions: drop water amount is 30.5 mm/min duration: 4×2.5 min(10 min in total).

(3) the IPX 3

Water spray test test method:

A. Test the Entel Marine radio equipment for pendulum pipe spraying test device: sample placement for pendulum pipe spraying test device: select pendulum pipe with appropriate radius, make the height of sample table at the position of pendulum pipe diameter, put the sample on the sample table, make the distance from the top to the sample nozzle is no more than 200mm, and the sample table is not rotated. Test conditions: the water flow was calculated according to the number of sprinkling holes in the pendulum pipe, each hole was 0.07l /min. When the water was sprayed, the water from the sprinkling holes on both sides of the middle point of the pendulum pipe was sprayed to the sample. The sample was placed in the center of the semicircle of the pendulum tube. The pendulum tube swings 60° on both sides of the vertical line, a total of 120°. Each swing (2×120°) is about 4s test time: continuous water spraying for 10 min.

B. nozzle type water spray test test equipment, hand-held shower water splash water test device sample placed: make the test at the top to the handheld shower sprinkler parallel distance between 300 mm to 500 mm test conditions: the trial should be installed with a balance weight, water flow of 10 L/min test time: according to the shell surface area calculation, test sample for 1 min per square meter area (not including installation), at least 5 min.

The IPX four (4)

Splash test test method:

A. Swing pipe splash test equipment and sample placement: same as the above IPX 3 type a; Test conditions: same as paragraph a of IPX 3 above except for the following conditions; The spraying area is the spraying water to the sample from the water holes in the arcs of 90° on both sides of the middle point of the pendulum tube. The sample was placed in the center of the semicircle of the pendulum tube. The pendulum tube swings 180° on both sides of the vertical line, about 360° in total. Each swing (2×360°) is about 12s. The test time is the same as that of the above IPX 3 type a (i.e., 10 min).

B. Nozzle type splash test equipment and sample placement: same as the above IPX 3 item b; Test conditions: remove the baffle with balancing weight installed on the equipment, and the rest are the same as the above IPX 3 item b; Test time: same as the above IPX 3 item b, i.e., 1 min per square meter (excluding installation area) based on the outer surface area of the sample to be tested, at least 5min.

The IPX five (5)

Test conditions: the distance between the test sample and the nozzle is 2.5m ~ 3m, and the water flow is 12.5l /min (750 L/h).

The IPX six (6)

Method name: intense water spraying test; Test conditions: the distance between the test sample and the nozzle is 2.5m ~ 3m, and the water flow is 100 L/min (6000 L/h).

The IPX seven (7)

Test equipment and test conditions: immersion tank. The size should be such that after the sample is put into the immersion tank, the distance from the bottom of the sample to the water surface should be at least 1m. The distance from the top of the sample to the water surface should be at least 0.15m.

The IPX eight (8)

Method name: continuous diving test; Test equipment, test conditions and test time: shall be harsher than IPX 7 as agreed by the parties.

That's all for the sharing, thanks for your reading, and we also supply waterproof Marine Radio for sale, if you have any demand for our products, just feel free to contact us.